Skip to content
AWOK Dual Touch v3

AWOK Dual Touch v3

€160.00 - €160.00
€160.00 - €160.00

Dedicated Wifi/BLE Touch screen wardriving accessory for Flipper Zero.

Elevate your wireless audits and offensive wifi engagements with the Dual Touch v3.

Add Accessories

🟢 In Stock
🟢 Dispatched today
Less than 40 minutues remaining for same-day shipping!
⬤ In Stock (🇪🇺 EU)
⬤ Dispatched
⏰ Order within for same day shipping

The AWOK Dual Touch v3 is a purpose-built wifi wardriving device for the Flipper Zero. Device operations are managed via the touch-screen; logs are ingested and saved via the Flipper Zero. The on-board GPS receiver guarantees accurate mapping and timestamping of all operations - allowing auditors hands-off, automated operation once activated.

Wardriving, or wifi mapping & analysis is a vital element of pentesting and security auditing.

For red-teams, penetration testers & offensive security auditors:

  • Pre-engagement reconnaissance: Assessment of client networks during authorized security audits
  • Vulnerability assessment: Identify weak encryption (WEP, WPA) in client networks
  • Evil twin detection: Find unauthorized access points mimicking legitimate networks
  • Probe Request Sniffing: Identify a target's geographical centers of interest
For corporate security and blue-teams:
  • Rogue access point detection: Identify unauthorized WiFi devices employees plug into corporate networks
  • Network perimeter auditing: Map your organization's WiFi footprint to ensure no sensitive SSIDs are visible outside buildings
  • Compliance verification: Document that networks meet security standards (WPA3 adoption, hidden SSIDs where required)
  • 1
  • 2
  • 3
  • 4

1. Dual Wifi/BLE Controllers

Dual ESP32 controllers for running parallel tasks: Evil Twin + Deauth, Wifi Wardrive + Probe Request Sniffing, etc.

2. Simultaneously Shared GPS

On-board GPS + Real-time Clock, simultaneously to both ESP Controllers. Onboard coin-cell battery for rapid startup.

3. DIP Switch Configuration

Configure the hardware to match your engagements with the on-board DIP Switches.

4. Impact resistant plastic shell

High-impact resistant plastic injection molded case & GPIO pin protection cover.

Detailed functionality

Wifi:

  • AP Scanning: Detect nearby WiFi networks.
  • Station Scanning: Monitor connected WiFi clients.
  • Beacon Spam: Broadcast customizable SSID beacons.
  • Deauthentication Attacks: Disconnect clients from specific networks.
  • WiFi Capture: Log probe requests, beacon frames, deauth packets, and raw data (requires SD card or compatible storage).
  • Evil Portal: Set up a fake WiFi portal with a custom SSID and domain.
  • Pineapple Detection: Detect Wi-Fi Pineapples and Evil Twin Attacks.
  • Web-UI: Built-in interface for changing settings and sending commands easily.
  • Wifi Wardriving: Log, timestamp and geo-stamp detected APs and Beacons via inbuilt GPS.

BLE:

  • BLE Scanning: Detect BLE devices, including specialized modes for AirTags, Flipper Zeros, and more.
  • BLE Packet Capture: Capture and analyze BLE traffic.
  • BLE Wardriving: Map and track BLE devices in your vicinity.
  • BLE Device Spam: Spoof/spam BLE accessories to nearby devices.
  • BLE Wardriving: Log, timestamp and geo-stamp detected beacons and devices via inbuilt GPS.

Firmware Control:
Users have full control over choice of firmware; the Dual Touch v3 supports multiple open-source firmware images, depending on user requirements:

  • General Wardriving: Optimised for classical war-driving, saved data compatible with WiGLE.net
  • Passive Assessment: Passive data collection for later analysis
  • Offensive Engagement: Evil Portal, De-authentification, Evil Twin, etc

DUAL TOUCH V3 vs FEBERIS PRO

While both devices share some common elements (Flipper Zero Compatibility, ESP32-based devices), their use cases are quite different.

The Dual Touch v3 is purpose built for Wifi Wardriving and Auditing. Its dual wifi/ble chip architecture and touch screen UI allows for optimised Wifi & BLE collection and auditing.

The FEBERIS PRO is a multi-frequency wireless audit device: It has two sub-GHz modules, one 2.4GHz module, and also a Wifi+BLE module. It is designed specifically multi-protocol RF audit and penetration.

HANDS ON: DUAL TOUCH v3

What's included

  • 1x AWOK Dual Touch v3
  • 1x GPIO Protective Cover

Dual Touch Resources